, , ,

Cylindrospermopsin Detection Kit (Rapid – Freshwater Streams and Source Water)

$215.00

 

  • Screening of Cylindrospermopsin in water samples at or above 30ppt
  • Format: 15 tests (5 samples at 2 dilutions/5 controls)
  • 5 – 10X Sample Dilution Buffer
  • 5 – 1X Sample Dilution Buffer
  • 5- Negative Control
  • 10- Fixed Volume Pipettes
215215
Sample Dilution Buffer
Optional extra sample buffer for this rapid test kit. Your kit already includes enough buffer for its tests; add a 5 or 10 pack if you need to dilute samples that read above the kit's range, re-run samples, or keep spare buffer on hand for field work.
$60.00
$100.00
Addons Price: $0.00
Total Price: $215.00
- +

The Cylindrospermopsin Detection Kit (Rapid – Freshwater Streams and Source Water) is a cylindrospermopsin rapid test for screening freshwater source water, drinking water and recreational water samples at 30 ppt (parts per trillion). Each sample is run undiluted and at a 10-fold dilution, so one kit covers both a low screening level and the range of the EPA drinking water health advisories. Results are ready in 30 minutes.

The kit contains 15 lateral flow cassettes, enough for 5 samples at two dilutions plus 5 negative controls, along with pre-measured 1X and 10X sample dilution buffers and fixed-volume pipettes.

Key Features

  • Screening level: a test line lighter than the negative control indicates 30 ppt or more. No visible test line indicates 1 ppb or more.
  • Two-dilution format: an undiluted and a 10-fold diluted run for each sample. The manual lists the intended screening levels as 30 ppt and 3,000 ppt.
  • Run time: 30 minutes per cassette.
  • Sample types: freshwater source water, drinking water and recreational water.
  • Simple handling: fixed-volume 200 µL pipettes and pre-filled dilution tubes, with no calibrated pipettor needed.
  • Room-temperature storage: store the kit at 2–30 °C, with cassettes sealed in their pouches until use.

What’s in the Kit

Each cylindrospermopsin rapid test kit includes:

  • 15 Cylindrospermopsin lateral flow cassettes (individually foil-pouched with desiccant and a disposable pipette)
  • 5 tubes of 1-fold (1X) Sample Dilution Buffer
  • 5 tubes of 10-fold (10X) Sample Dilution Buffer
  • 5 Negative Control tubes
  • 10 Fixed-volume pipettes

You will also need: a timer, a marker for labeling, and a water sample collection bottle (Attogene catalog number CO2024). For on-site testing with collection supplies included, see the Cylindrospermopsin Detection Kit (Rapid – Recreational Water).

Who It’s For

  • Drinking water utilities monitoring source water during cyanobacterial bloom season
  • State and municipal water quality programs sampling streams, rivers and reservoirs
  • Environmental consultants who need a quick screen before sending samples for confirmation
  • Research groups studying cyanotoxin occurrence in freshwater

How to Use the Cylindrospermopsin Rapid Test

  1. Wearing gloves, collect water into a labeled sample bottle. Refrigerate for up to 5 days, or freeze for longer storage.
  2. Bring cassettes, buffers and samples to room temperature.
  3. Run the negative control first: transfer 200 µL from the Negative Control tube into a cassette’s sample port and start a 30-minute timer.
  4. Using a fixed-volume pipette, add 200 µL of sample to the 1X dilution tube and mix well.
  5. Transfer 200 µL from the 1X tube into the 10X dilution tube and mix by inverting several times.
  6. Add 200 µL from each tube to its own cassette and start a 30-minute timer.
  7. Read results within 5 minutes after the run is complete.

Full instructions are in the AU2058 product manual (PDF).

Reading Your Results

  • Test line as dark as or darker than the negative control’s test line: below the limit of detection
  • Test line lighter than the negative control’s test line: 30 ppt or more
  • No test line (control line only): 1 ppb or more

A visible control line is required for a valid result. Remember to account for the dilution factor. For example, a sample at 3,000 ppt shows no test line on the undiluted run and almost no visible test line on the 10-fold run. For semi-quantitative estimates in the 0–1 ppb range, run cylindrospermopsin standards alongside your samples.

Cylindrospermopsin and EPA Guidance

Cylindrospermopsin is a tricyclic alkaloid cyanotoxin of about 415 Da produced by certain cyanobacteria, including Cylindrospermopsis raciborskii. It is highly water soluble, so it can persist in reservoirs and source water after a bloom.

The EPA 10-day drinking water health advisory for cylindrospermopsin is 0.7 ppb (700 ppt) for children under six and 3 ppb (3,000 ppt) for older children and adults. For recreational water, the product manual cites a draft EPA criterion of 8,000 ppt; EPA’s final 2019 recreational criterion is 15 µg/L. Check with your state agency for the values that apply to you.

Frequently Asked Questions

How sensitive is the cylindrospermopsin rapid test?

The undiluted run screens at 30 ppt. If no test line appears, the sample contains 1 ppb or more.

Why run each sample at two dilutions?

The 10-fold dilution extends the screening range up to the level of the EPA health advisories, so you can tell a trace detection apart from a high-concentration sample.

How many samples does one kit test?

Five. Each sample uses three cassettes: undiluted, 10-fold diluted and a negative control, for 15 cassettes in total.

Is the cylindrospermopsin rapid test quantitative?

No. It provides preliminary qualitative results. Confirm samples that require action by ELISA, such as the Cylindrospermopsin ELISA Kit (EL2047), or by HPLC.

What other cyanotoxin tests do you offer?

See the Microcystin Test Kit (Rapid – Recreational Water) and the Anatoxin-a Detection Kit.

For research use only. Not for use in diagnostic procedures. Questions? Call 512-333-1330 or email sales@attogene.com.

tests

5 tests, 20 tests

You may also like…

Shopping Cart